College of Science/ University of Mosul
Rafidain Journal of Science
1608-9391
17
6
2006
05
01
Determination of Radioactive Contamination of Plant Fertilizers Using CR-39
تحديد التلوث الإشعاعي في الأسمدة النباتية باستخدام CR-39
1
10
43352
10.33899/rjs.2006.43352
EN
Mohsin
M. Al-Badrani
Journal Article
2006
05
01
The aim of this research is to study the fertilizers that are widely used due to what they can cause of an increment in natural radioactive level of soil, and due to what will affect the increase in the environmental contamination level with radiation.
The concentrations of (Rn-222) and (U-238) of seven kinds of local and imported fertilizers are calculated.
In the present work an investigation has been performed using nuclear track detectors (CR-39) technique with the use of test tubes (2.0-2.1 cm) in diameter. The chemical etching is utilized by NaOH with normality (6.25 N) at (70 oC 1oC) temperature and (4hrs) etching time.
The obtained results indicate that there is a remarkable increase in Radon and Uranium concentrations especially, the Iraqi fertilizers with both kinds of compound and compound -27, while the concentrations of Radon and Uranium for other types are approximately the same, except that of Sulphar fertilizer which shows a lower concentration.
يهدف البحث إلى دراسة مستوى التلوث الإشعاعي في عينات منتخبة من الأسمدة النباتية شائعة الاستخدام، نظراً لما تسببه هذه الأسمدة من زيادة في مستوى الإشعاع الطبيعي للتربة، ومدى تأثير ذلك على زيادة مستوى التلوث البيئي بالإشعاع.تم حساب تراكيز كل من الرادون (Rn-222) واليورانيوم (U-238) لسبعة أنواع من الأسمدة النباتية المحلية والمستوردة. أجريت الدراسة باستخدام تقنية كاشف الأثر النووي (CR-39) بواسطة أنابيب الاختبار ذات القطر (2.0-2.1 cm)، تمت عملية القشط الكيميائي باستخدام هيدروكسيد الصوديوم NaOH عياريته (6.25N) عند درجة حرارة قشط (70 oC 1oC) وزمن قشط (4hrs).تشير النتائج إلى وجود زيادة ملحوظة في تراكيز الرادون واليورانيوم في السماد العراقي بنوعيه المركب والمركب 27-، في حين كانت التراكيز متقاربة في بقية الأنواع، عدا سماد الكبريت حيث كان تركيز الرادون واليورانيوم فيه منخفضاً.
https://rsci.mosuljournals.com/article_43352_6a0f2bdb882b2bd67ea8d94f1f4935bc.pdf
College of Science/ University of Mosul
Rafidain Journal of Science
1608-9391
17
6
2006
05
01
Refractive Index of Oils Measurement by Using Fiber Optics
استخدام الليف البصري في قياس معامل انكسار الزيوت
11
21
43353
10.33899/rjs.2006.43353
EN
Watfa
Kh. Younis
Journal Article
2006
05
01
In this research, fiber optics (FO) of type Plastic Clad Plastic (PSP) is used as sensor to measure refractive index of oils, lens oil and machine oil. Hadrolic and automobiles oils are not used because the impurities they have. Fiber optics is used to measure the change of refractive index of lens oil and machine oil with the temperature variations and compared the results with those measured by Abbe Refractometer the results were in good agreement .The fiber - fiber coupling technique is used in this project as a sensor to measure the change of refractive index of lens oil and machine oil with the change of temperature.
في هذا البحث تم استخدام الليف البصري نوع PCP المتعدد الأنماط كمجس لقياس معامل انكسار الزيوت منها زيت العدسة و زيت الماكنة ولم يستخدم زيت الهادر وليك وزيت السيارات لوجود شوائب فيهما. تم استخدام مجس الليف البصري لقياس تغير معامل انكسار الزيوت (زيت العدسة، زيت الماكنة) مع درجات الحرارة المختلفة ومقارنة النتائج مع تلك المقاسة في جهاز Abbe Refractometer فجاءت مطابقة تقريباً. وقد اعتمدت طريقة اقتران ليف- ليف لقياس معامل انكسار زيت العدسة وزيت الماكنة وتغير معامل انكسارهما مع تغير درجة الحرارة ولقد لوحظ أن هذه الطريقة كفوءة عندما يتطابق معامل انكسار الزيت مع معامل انكسار قلب الليف البصري core.
https://rsci.mosuljournals.com/article_43353_c70832965c0a2665fa765aa888c87091.pdf
College of Science/ University of Mosul
Rafidain Journal of Science
1608-9391
17
6
2006
05
01
Using of Nickel Oxide NiO as a Diffusion Barrier in Aluminide Coating on Austinitic Stainless Steel AISI 321
استخدام أوكسيد النيكل NiO كحاجز انتشاري لعملية الطلاء بالألمنيوم لسبيكة الصلب الأوستينايتي AISI 321
22
32
43355
10.33899/rjs.2006.43355
EN
Yahya
A. Al-Salman
Moayad
A. Mohammad
Journal Article
2006
05
01
Aluminum compounds are the most effective to resist the oxidation and corrosion at high temperature, because it has a good ductility and its capability to form a protective oxide scale Al2O3, such Alumina scale is known as thermally and electrically insulator and characterized with slow gowning rate. In this research we tried to prepare aluminide coating on austinitic stainless steel AISI 321, using a pack-cementation technique. The alloy surfaces were doped with a thin nickel oxide layer before aluminising using an adhesive materials. The coating produced was subjected to a cyclic oxidation and hot corrosion tests. The coating structure and coating behaviour after the treatment were studied using X-rays and optical microscope. The coatings produced were posses a high resistance to oxidation under atmospheric pressure at 900°C, but not in presence of a molten salt Na2SO4 at 884°C.
تعدّ المركبات الألومينية الأكثر فعالية لمقاومة التأكسد والتآكل في درجات الحرارة العالية وذلك لامتلاكها لدانة جيدة، فضلاً عن كونها قادرة على تكوين القشرة الأوكسيدية الواقية AL2O3 والتي تعدّ بدورها عازل حراري وكهربائي جيد ويتميز ببطئ معدلات نموها. حاولنا في هذا البحث تحضير طلاءات الومينية على سطح سبيكة الصلب (AISI 321) باستخدام طريقة السمنته Pack-Cementation بعد أن تمّ تطعيم سطح السبيكة بطبقة رقيقة من أوكسيد النيكل باستخدام مواد لاصقة. وقد تمّ تعريض هذه الطلاءات لعمليات الأكسدة والتآكل الدوري في درجات حرارة عالية لتحديد مدى مقاومتها والتعرف على سلوكيتها ودراسة التراكيب لهذه الطلاءات عن طريق الفحص المجهري والأشعة السينية، تشير النتائج أن هذه الطلاءات لها مقاومة جيدة للتأكسد تحت الضغط الجوي الاعتيادي وفي درجة 900م°، في حين لم تقاوم التأكسد بوجود منصهر الملح Na2SO4 في درجة انصهاره 884م°.
https://rsci.mosuljournals.com/article_43355_98e2065c192e87c6866f078454f2f2e4.pdf
College of Science/ University of Mosul
Rafidain Journal of Science
1608-9391
17
6
2006
05
01
Electrical Properties of Thin Film Capacitors of Polymeric Alloys
الخواص الكهربائية للمتسعات ذات الغشاء الرقيق من السبائك البوليمرية
33
44
43359
10.33899/rjs.2006.43359
EN
Rana
Z. Al-Flayh
Yahya
N. Al-Jammal
Journal Article
2006
05
01
In this work, a parallel plate capacitor with insulating polymeric thin film from pure material of long chain Poly Metheyl Meth Acrylates (PMMA) and short chain of Poly Carbonates (PC) and Poly Methylene (PM) as well as of alloys (PMMA + PM). In order to get a good thickness, we used rotating technique.
The current-voltage characteristic for these capacitor of a thickness (2000 oA) had been studied at room temperature. The breakdown voltage value were found for pure polymer of (PMMA), (PC) and (PM) equal to (1700 V), (2800 V) and (2000 V) respectively. But the breakdown voltage for alloys (75% PMMA + 25% PM), (50% PMMA + 50% PM), (25% PMMA + 75% PM), (75% PC + 25% PM),
(50% PC + 50% PM), (25% PC + 75% PM) and (33.3% PMMA + 33.3% PC + 33.3% PM) are (2000 V), (1850 V), (1750 V), (2500 V), (1950 V), (1800 V) and (1500 V) respectively. The results have shown the behavior sequence breakdown in those capacitor.
Finally, loading time for the thin capacitor which is consisted of (PMMA + PC), (PC + PM) and (PMMA + PC + PM) as a function of the numbers of breakdown has been studied, where it is found that the loading time increases with breakdown numbers increasing, and according to the results we have closed the best fabricated capacitor from (50% PMMA + 50% PM) alloy which we have found it to have a high loading time.
تم في هذا البحث تصنيع متسعات الألواح المتوازية ذات الغشاء البوليمري العازل من مواد نقية ذات سلاسل طويلة من مادة البولي مثيل ميثا اكريلايت Poly Methyl Meth Acrylates (PMMA) وذات سلاسل قصيرة من مادة البولي كاربونات Poly Carbonates (PC) والبولي مثيلين Poly Methylene (PM)، وكذلك من سبائك (PMMA + PM) و (PC + PM) و(PMMA + PC + PM). ولغرض الحصول على غشاء رقيق عازل بسمك واحد استخدمنا طريقة تقنية الطرد المركزي. تم دراسة خواص التيار-الفولتية لهذه المتسعات، ومن خلال هذه الخواص تم تحديد فولتيات انهيار المتسعات ذات سمك واحد (2000 oA) وفي درجة حرارة الغرفة. لقد وجد أن قيمة فولتيات الانهيار للبوليمرات النقية (PMMA) و (PC) و (PM) تساوي 1700 V و 2800 V و 2000 V على التعاقب. بينما وجدت قيم فولتيات الانهيار للسبائك (75% PMMA + 25% PM) و (50% PMMA + 50% PM) و (25% PMMA + 75% PM) و (75% PC + 25% PM) و (50% PC + 50% PM) و (25% PC + 75% PM) و (33.3% PMMA + 33.3% PC + 33.3% PM) هي 2000 V و 1850 V و 1750 V 2500 V و 1950 V و 1800 V و 1500 V على التعاقب. ولقد أظهرت جميع النماذج صفة الانهيار المتعاقب. ومن خلال دراسة خواص التيار-الفولتية وجد أن التوصيل الأومي كان متغلباً عند الفولتيات الواطئة. إن تصرف التيار المحدد بشحنة الفراغ تم ملاحظته أيضاً. وأخيراً، تم دراسة زمن تحميل المتسعات ذات الأغشية الرقيقة المصنعة من السبائك (PMMA + PM) و (PC + PM) دالة لعدد الانهيارات، حيث وجد أن زمن التحميل يزداد بزيادة عدد الانهيارات. وعلى ضوء النتائج تم اختيار أحسن متسعة من سبيكة (50% PMMA + 50% PM) حيث وجد أنها ذات زمن تحميل عالي.
https://rsci.mosuljournals.com/article_43359_51aee85b2b06beaf4db3ffecf1735723.pdf
College of Science/ University of Mosul
Rafidain Journal of Science
1608-9391
17
6
2006
05
01
Molecular Reform of Hydrocarbonic Liquid by Microwaves
إعادة التشكيل لجزيئات سائل هيدروكاربوني بالموجات الدقيقة
45
61
43361
10.33899/rjs.2006.43361
EN
Hazim
S. Al-Hadidi
Anwar
M. Al-Faydhi
Journal Article
2006
05
01
In this work, the effect of microwaves on the hydrocarbonic liquid was studied. Small amounts of hydrocarbonic liquid were irradiated by microwave with different applied powers (220, 360, 600) Watt. Through tests and physical calculations of the irradiated samples of the hydrocarbonic liquid with different surface area, a major difference was found compared with the control samples. Carbon sediments were also noticed. The most important result is that each test revealed major differences that the octane No.(R+m/2). change from (43.6) to (93) at (600) Watt operated power. This indicates that molecular reform of hydrocarbonic liquid using microwave is a new and original method to enhance the octane No. This scientific fact which is not mentioned in any previous researches was explained throughout former researches dealing with the effect of microwaves, keeping in mind that the expected heat effect was studied by repetition of all the measurements under heat effect only.
تم في هذا البحث دراسة تأثير الموجات الدقيقة (Microwaves) على سائل هيدروكاربوني. تم تعريض كمية محددة من مادة هيدروكاربونية للموجات الدقيقة وبقدرات تشغيلية مختلفة للمدى (220, 360, 600) Watt. ومن خلال الاختبارات والحسابات لبعض الكميات الفيزيائية التي أجريت على المادة المشععة من السائل الهيدروكاربوني مثل (الكثافة، التوصيلية الحرارية، الحرارة النوعية والشد السطحي …) لنماذج بمساحات سطحية مختلفة، وجد تباين واضح كما لوحظ أيضا وجود راسب كاربوني مقارنة مع النماذج غير المشععة مما يدل على حدوث إعادة تشكيل (Reform) جزيئي. إنّ النتيجة الأهم التي تم التوصل إليها هي انه عند فحص النماذج المشععة وجد أنّ المركبات الأساسية في تكوين السائل الهيدروكاربوني قد اختلفت نسبها بشكل واضح كما ارتفع الرقم الاوكتاني (Octane No.) للنموذج من (43.6) إلى (93) عند قدرة تشغيلية (600) Watt . وهذا مؤشر على ان اعادة التشكيل الجزيئي بالموجات الدقيقة لهذا المقطع الهيدروكاربوني يمكن ان يكون طريقة جديدة ومبتكرة لتحسين الرقم الاوكتاني. هذه الحقيقة العلمية لم يتم التطرق إليها في بحوث سابقة، وقد تم استنباط تفسير لها مستخلص من بحوث سابقة وقريبة من موضوع البحث حول تأثيرات الموجات الدقيقة، علماً بأنّ التأثيرات الحرارية المتوقعة قد تم تحديدها بإعادة جميع القياسات ولكن تحت تأثيرات الحرارة فقط ومقارنتها مع نتائج الموجات الدقيقة.
https://rsci.mosuljournals.com/article_43361_01fd85472fb0602bdcbd15f6930cc0d5.pdf